Projects

Cell to Module

Across the battery lifecycle

01 / 05

Electrode

R&D / Pilot

Electrode coating process development — slurry, slot-die coating, and drying, dialing in loading, adhesion, and uniformity at R&D and pilot scale.

Cell to Module

Across the battery lifecycle

01 / 05

Electrode

R&D / Pilot

Electrode coating process development — slurry, slot-die coating, and drying, dialing in loading, adhesion, and uniformity at R&D and pilot scale.

02 / 05

Separator

R&D / Pilot

Separator evaluation and integration — testing coated separators for lithium-metal and lithium-sulfur cells through R&D and pilot builds.

03 / 05

Cell Assembly

Mass Production

High-volume prismatic cell assembly — jelly roll tab welding, top-cap joining, casing insertion, and seam welding; plus laser welding, insulation wrapping, and ultrasonic welding on 24/7 production lines.

04 / 05

Electrolyte & Activation

R&D / Pilot

At Lyten, electrolyte formulation and cell activation — additive studies, controlled filling, and formation cycling for lithium-metal and lithium-sulfur chemistries.

05 / 05

Module

Mass Production

Module and pack manufacturing — cell stacking, robotic assembly, interconnect welding, and busbar welding at production volume.

Projects

Selected work.

LFP · High volume · Current · Tesla

LFP cell & module assembly line

Own the LFP cell and module stack assembly processes for 24/7 high-volume production at Tesla, with 15% cycle-time reduction and process capability held above Cpk 1.67. Drive yield across laser, ultrasonic and hot-melt welding and leak detection through structured root-cause analysis, lifting line rolled yield 10%. Configure MES data collection with in-line SPC and build dashboards tracking failures by fixture, track and batch.

SPCMSAPFMEAOEEDMAICMES

Figure: prismatic LFP cell assembly sequence (a–f), from a Tesla Model 3 cell teardown. Stock, S. et al., "Cell teardown and characterization of an automotive prismatic LFP battery," Electrochimica Acta 471 (2023) 143341, doi:10.1016/j.electacta.2023.143341. CC BY 4.0.

LFP · High volume · Tesla

Station commissioning & line ramp

Led commissioning, qualification and ramp of seven new cell assembly stations with domestic and international OEM suppliers: process flow mapping, equipment function definition, fixture design improvement and validation, mechanical checks, dry and wet runs, PFMEA, GR&R, error proofing, MES configuration, control plans and SOPs, through OEE demonstration, buy-off and integration into the mass-production line. Throughput ramped from hundreds to tens of thousands of cells per day; the module stack line from 20% to 80% of design capacity at stable output.

CommissioningGR&RBuy-offOEM suppliers

Lithium-metal · Pilot · Lyten

Li-metal anode coating scale-up

Scaled polymer coating and lithium-metal foil production from formulation trials to a pilot-line process, a 100× throughput increase via extrusion, lamination and precision rolling, holding tight dimensional tolerance and cosmetic quality, with defect rates cut over 40%.

DFMCoatingYield100×

SEM comparison of bare vs. protective-coated Li metal, with cross-section and elemental mapping. Ordaz, M.V. et al., ACS Appl. Mater. Interfaces 16(49) (2024) 68237–68246, doi:10.1021/acsami.4c13335. CC BY 4.0.

Lithium-sulfur · Research · Lyten

Li-S characterization & electrochemistry

Ran electrochemical testing (EIS, CV, GITT/PITT) and materials characterization (SEM/EBSD, XRD) on Li-S cell components, tying degradation mechanisms back to formulation and process decisions.

ElectrochemistrySEMXRDLi-S

Design targets and approaches for a practical Li-S cell (energy density, N/P ratio, E/S ratio, sulfur loading). Batteries 9(1) (2023) 27, doi:10.3390/batteries9010027. CC BY 4.0.

LFP · High volume · Tesla

Top-cap weld fixture redesign

Replaced consumable PEEK tape on the top-cap laser welding fixture with a screw-fastened PEEK block, eliminating the tape placement variation that was driving weld quality variation and yield loss, and extending the replacement interval from every 3 days to every 2 weeks. Changeover time and unplanned downtime both fell.

Fixture designError proofingDowntime

Cross-cutting · Lyten and Tesla

SPC & validation data pipeline

Built Python and JMP tooling to automate data collection, visualization and database generation, then MES-fed SPC and OEE dashboards with automated Cpk trend reporting, alerting process and maintenance teams to drift early enough to correct before NG product was produced, worth roughly 2% yield per station.

PythonSQLJMPSPC

Solid-state · Research · Sakuu Corp.

Solid-state assembly fixtures

Designed and improved cell assembly and test fixtures for solid-state and lithium-metal prototypes, achieving uniform pressure distribution and reproducibility, and ran the mechanical failure analysis that drove the assembly process changes behind it.

Fixture designPressure mapping

Cell fixture assembly with pressure calibration locations. Commun. Mater. 3, 100 (2022), doi:10.1038/s43246-022-00286-8. CC BY 4.0.

Advanced manufacturing · Research · Purdue

Laser additive manufacturing system

Designed an SLM system integrated with CNC machining plus a custom high-pressure gas chamber, applying DOE and tolerance validation to establish process repeatability for metal and ceramic component fabrication.

Selective laser meltingSystem designDOE

Schematic of a laser-wire directed energy deposition system. Abuabiah, M. et al., Materials 16(5) (2023) 2030, doi:10.3390/ma16052030. CC BY 4.0.

Lithium-sulfur · Research · Lyten

Li-S composite anode

Co-developed the lithium-metal composite anode and protective-coating formulation that mitigates anode degradation in Lyten's lithium-sulfur platform, from formulation trials through validation and scale-up.

Patent WO2024259126A3Lithium-metalLi-S

Failure modes at the Li-metal anode—electrolyte interface (dendrite, LiPS corrosion, dead Li). Adapted from Energy Material Advances 4:0010 (2023), doi:10.34133/energymatadv.0010. CC BY 4.0.